Render on Metal Lath - Guide

External Plastering (Rendering on Metal Lath Using St. Astier Products)

Link to Wusheng Hardware

The main difficulty in working on lath is ensuring the lath is suitable for the job. Metal laths come in a wide variety of types and designs, some of which have specific functions and are not suitable for a broad range of rendering applications. It is imperative to check with the manufacturer of the lath what is it designed to cope with.

The lath Manufacturers recommendations for fixing should be sought, however as most fixings are specified to accommodate cement renders or plasters, it may be necessary to decrease the centers of the fixings to 4&#; (100mm). to reduce to the minimum any movement during application. Laps should be firmly fixed.

Lath can be plastic, metal, galvanized or stainless steel. All can be used with NHL mortars.
Simple expanded mesh lath usually requires greater numbers of fixings to reduce play.
The ribbed laths span more readily between supports and are generally more robust.

Backgrounds:
Brick, block, concrete or even straw bales. It is also commonly used on framing, either timber or metal studs or to bridge between two completely different backgrounds and supports. If the work spans over two different types of backgrounds, the choice of application and mix will be determined by the weaker support.

Application:
Ensure that the first coat covers the laths by a minimum of 5/16&#; &#; 3/8&#; from the outside face of the metal (including any ribs or overlaps), particularly where the lath is spanning between framing.

First coat: use NHL 5 and a well graded sharp sand at a ratio of 1:2. The mortar must be allowed to cure and harden sufficiently, at least 1 week in good weather conditions, longer if possible, before a second coat is applied. Internal work should not be force
dried under any circumstances.

If you are looking for more details, kindly visit Flat Rib Lath.

Further coats can be applied as per the general guidelines for NHL Renders and plasters (2 or 3 coat work).
Where lath is well fixed to a solid background, use of a spray gun with a NHL 5 1:1.5 can be used for the first and all subsequent coats.

Protection and curing:
Always follow best working practice, pay particular attention to protection against knocks and bumps on fresh mortars.

Note:
If lath has been fixed by another trade, the plasterer should only apply NHL mortars when he is fully satisfied that the lath work is rigid and sound.

The RBL Rib Lath provides plaster/render backing and is also suitable for the refurbishing of damaged or deteriorated faces of masonry walls. Available in galvanised for internal use and stainless steel for external use.

Installation:

• Fixing of lath should follow BS EN -1: Internal Plastering and BS EN - 2: External Rendering.
• The apex of rib lath should always be in contact with the fixing background.
• Fixing of lath should follow BS EN -1: Internal Plastering and BS EN -2: External Rendering.
• The apex of rib lath should always be in contact with the fixing background.

Fixing to metal or timber supports:

The company is the world’s best Metal Wall Corner Protectors supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.

• Timber: Use 38 x 7mm plasterer&#;s nails or 32 x 2mm staples to fix with ribs running at 90° to timber studs which should be at a maximum 600mm centres.
• Metal: Use 1.63mm or two strands of 1.22mm galvanised mild steel wire to tie around the rib where it crosses each steel stud.
• Steel studs should be at maximum 600mm centres. To join sheets of Rib Lath, the edge ribs should be overlapped and the edges tied at 150mm centres with 1.22mm tying wire.
• Where the ends of the lathing finish in front of a support, overlap by 50mm, otherwise sheets should be overlapped by 100mm with two 1.63mm ties used with each overlapping rib.
• Fixing to solid backgrounds: The ribs of the lath should be held firmly against the background by the use of fixings placed at 600 mm centres.
• End edges should be overlapped by 50mm, side edges by 25mm and tied or screwed at 150mm centres. We strongly recommend the use of Stainless Steel for external applications.