Hardfacing with wire welder - The Home Machinist!

May. 06, 2024

Hardfacing with wire welder - The Home Machinist!

Post by dgoddard » Sun Nov 11, 2012 10:43 am

For more information, please visit Sale Hardfacing Wire.

warmstrong1955 wrote:Mmmmm....a manual stump cutter......

I'm familiar with a few different brands of gasoline & diesel stumpcutters....as well as excavator attachments, but I've never seen a manual one. Interesting... Bill

It consists of a 1 inch steel bar about 55 inches long ground or milled on one end to provide a geometry that allows for a strong weld to a 3 inch wide, 6 inch long 1/2 inch thick blade with a 30 degree chisel edge with a small edge bevel at about 45 degrees . The rod is given a light knurl to allow for good grip without being so harsh as to rough up the hands. The bar is not used to attack the roots directly, but rather is used with vertical strokes to split off pieces along the edge of the stump. The split fragments will run into the roots and can be broken or cut off resulting in taking the offending stump below ground level where it can be left to rot and not trip people or bust mowers or bend their blades. The method is reasonably efficient, avoids unnecessary dulling of the blade, and while it is a bit of work, is quite handy for smaller stumps, At 15 lbs being dropped and thrust into "end grain" it splits the chips off pretty effectively for about the same effort per stroke as digging with a "clamshell" post hole digger. Watch your feet, and I hope you don't have to carry it around a lot. I paint mine white with black or red bands so it is hard to loose if dropped into grass, weeds, snow, leaves, etc. and highly visible wherever it is on the work site.

Now as to the advisability of hardfacing deposited on the cutting edge. That short bit of 45 degree bevel at the end of the chisel point is where I was going to deposit the hard face material

The brochure from Horbart brothers says "has good resistance to abrasion and impact" and recommends it for applications such as:
• Bucket lips and teeth
• Cultivator chisels and sweeps
• Plow shares, scraper blades
They do however recommend preheat of the substrate to prevent cracking of the deposit on low alloy steels which are the primary intended substrate.

"

It consists of a 1 inch steel bar about 55 inches long ground or milled on one end to provide a geometry that allows for a strong weld to a 3 inch wide, 6 inch long 1/2 inch thick blade with a 30 degree chisel edge with a small edge bevel at about 45 degrees . The rod is given a light knurl to allow for good grip without being so harsh as to rough up the hands. The bar is not used to attack the roots directly, but rather is used with vertical strokes to split off pieces along the edge of the stump. The split fragments will run into the roots and can be broken or cut off resulting in taking the offending stump below ground level where it can be left to rot and not trip people or bust mowers or bend their blades. The method is reasonably efficient, avoids unnecessary dulling of the blade, and while it is a bit of work, is quite handy for smaller stumps, At 15 lbs being dropped and thrust into "end grain" it splits the chips off pretty effectively for about the same effort per stroke as digging with a "clamshell" post hole digger. Watch your feet, and I hope you don't have to carry it around a lot. I paint mine white with black or red bands so it is hard to loose if dropped into grass, weeds, snow, leaves, etc. and highly visible wherever it is on the work site.Now as to the advisability of hardfacing deposited on the cutting edge. That short bit of 45 degree bevel at the end of the chisel point is where I was going to deposit the hard face materialThe brochure from Horbart brothers says "has good resistance to abrasion and impact" and recommends it for applications such as:• Bucket lips and teeth• Cultivator chisels and sweeps• Plow shares, scraper bladesThey do however recommend preheat of the substrate to prevent cracking of the deposit on low alloy steels which are the primary intended substrate.

What is Hardfacing in Welding and How Can You Apply It?

What is Hardfacing and How Does it Work?

Hardfacing is a process where you use the general concept of welding – specifically the deposition of material – to coat the outside of a base metal with a tougher, harder metal. This can make the resulting workpiece more durable, more resistant to abrasion, wear, and damage, and expand its longevity. Hardfacing is performed using specialized electrodes or filler rods but largely uses the same kind of arc welding process to melt those fillers onto the surface of the base material.

This isn’t quite the same as something like adhering a shell to the outside of a workpiece. Since the welding process is used, the surface of the base material is melted enough to combine with the filler material, resulting in a merger of the two. This creates a thick, dense layer between 1 and 10 mm, made of a highly bonded, wear-resistant alloy combining the base and filler metals.

Hardfacing improves the surface strength, ductility, wear resistance, corrosion resistance, and erosion resistance of the original workpiece. It can be performed on cast iron, copper, and nickel alloys, stainless steel, carbon steel, and manganese steel.

One key to successful hardfacing is minimizing heat. While you need enough surface melt to the base material to adhere to the hardfacing filler, you want as little mixing as possible because the base material will soften the added material and reduce the utility of the hardfacing. Therefore, knowing what material you’re hardfacing is critical so you can identify ideal temperatures.

What Are the Benefits of Hardfacing?

Hardfacing is a way to strengthen and extend the working life of metal parts that see a lot of wear, particularly surface wear. By hardfacing a worn part, additional lifespan can be drawn from the base workpiece, extending longevity and reducing the need to replace it; this saves money over the long run.

Hardfacing is commonly used in agricultural and mining situations and is frequently also an option for getting more useful life out of a part while a replacement is on order. In remote locations or for specialized parts that need lead time to be made and shipped, when the difference is between halted operations and continued operations, hardfacing can make the difference.

Overall, hard facing can be used to minimize the downtime spent replacing worn or broken parts, allows you to store fewer replacements on-site if you typically do so, and increases the average lifespan of those parts. In many cases, the lifespan of a working piece can be extended by up to 300% with dedicated hard facing, which can mean overall savings for the company of 25% to 75% in the cost of replacements.

Where is Hardfacing Often Used?

Hardfacing can be used in a wide range of different applications. Since it’s coating the outside of a workpiece, it’s generally used on pieces that have to resist impacts or abrasions over time.

In construction, an excavator’s plow is one common piece that has to endure an immense amount of impact and erosion damage. Heavy use of an excavator can wear it down, reducing the strength of the plot and even the workable dimensions of the machine. Hardfacing the plow strengthens it against this kind of damage.

In agriculture, the manufacture of sugar involves crushing sugarcane in a roller. Despite being a plant – which you might not think of as being able to damage metal parts – the sugarcane plant is quite strong and can give as good as it gets. These rollers can be hard-faced to help resist the damage of continually crushing sugar cane and extend the operating life of the machine.

Another common example from mining is the crusher that breaks up larger chunks of ore-bearing material for processing. There are a wide range of different designs for these machines, but many of them end up using plates of metal and heavy motors to crush rock. Rock, too, resists being crushed and will damage and abrade the crusher over time. Hardfacing the jaws of the crusher will help them resist that force and can be used as a repair to restore functionality to damaged jaws before they need to be fully replaced.

Are There Different Techniques for Hardfacing?

The company is the world’s best china wear resistance plate supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.
Additional resources:
Best Abrasive Resistant Metal Vendor: How to Choose?

Understanding Conical Washer Dimensions: A Guide
Key Considerations to Keep in Mind When Selecting Sanitary IDF Union
What you should know about valves
Selection Criteria for SMT Placement Equipment
Bevel Gear: What Are They? How Do ...
10 Questions You Should to Know about Valve Housing wholesaler

Yes. Hardfacing can be performed in two ways: overlay and build-up. These are roughly equivalent to enhancing existing materials and repairing damaged materials.

Imagine a workpiece with many gouges, scratches, abrasions, dings, scrapes, and other forms of damage from long use. The workpiece is worn and nearing the end of its lifespan. Such a piece can be restored with hard facing using the build-up technique. Build-up hardfacing entails using the welding process to deposit hardfacing material and spending additional time and care on the deeper gouges and abrasions to rebuild the working surface of the workpiece. A layer to smooth and even out the working surface is applied, and any finishing is performed.

Overlay hardfacing can be done on pieces that have been built up already using the previous technique or on brand-new or barely-worn pieces that need additional reinforcement to expand their lifespan. This technique simply uses repeated and iterative passes of hard facing to deposit a layer of material across the entire surface of the workpiece; no special care is necessary for repairs because no repairs are necessary. It’s simply a method of reinforcement.

How is Hardfacing Performed?

The step-by-step process of hard facing is relatively simple and similar to many other welding processes. The primary difference is that it takes place over the whole surface of a typically large workpiece rather than along a single seam or crack in the workpiece.

Step one is to clean the part. Since hard facing is typically used on working machines, these have likely built up grime, dirt, oils, greases, rust, and chemicals, all of which can inhibit the performance of a weld and cause inclusions, weaknesses, and faults in the resulting surface. A thorough cleaning is required to avoid cracking, warping, and damage to the workpiece. This process may even need to be performed on brand-new pieces, particularly if they’ve been painted or coated in rust-resistant chemicals.

Step two is to perform build-up hard facing on any deep gouges, abrasions, cracks, or other damage to the surface of the workpiece. Hardfacing requires that the surface be more or less the shape and form you want the finished piece to be, so any repairs you need to make should be made at this step in the process. This isn’t necessary for new pieces you’re reinforcing with hard facing, as there’s likely no damage to repair.

Step three is to “butter” the part. Buttering is the act of forming a thin buffer layer between the base material and the hardfacing material. It’s most commonly used in cases where the two materials are dissimilar and will have a hard time bonding with one another. By using an intermediary as a buffer layer, you can create more comprehensive bonds and reduce the chances of the final coating cracking or shrinking and causing problems.

The fourth and final step is to perform the actual hard facing. This is where you apply your coats of hardfacing material. This may be spotty and sporadic, or it may be comprehensive and can be anywhere from one to three coats for most situations.

One critical component of the actual hardfacing process is deciding on a hardfacing pattern. While a complete coat of cladding can be used, this is often unnecessary, depending on the purpose of the workpiece. Other patterns include:

Dots. A dot pattern involves using a series of regularly spaced dot-shaped welds to deposit the hardfacing material across the surface. This is typically used on machines that deal with larger rocks and aggregate; smaller material can fill the gaps between the raised dots, while the raised dots become the source of impact and are strengthened against it. Other types of impact are cushioned by the “dead bed” between the dots.
Stringers. Stringers are long, straight beads of welding, typically spaced some distance apart, between a quarter of an inch all the way up to 1.5 inches. This is typically chosen with beads that run parallel to the direction the material flows in use, so it doesn’t “catch” and cause more damage to the hard-faced material.
Waffles. A waffle, criss-cross, or herringbone process is perpendicular beads that leave small square pockets behind. Again, this is usually used for dealing with larger aggregate materials, where smaller materials and sand form a cushioning bed in between.

All of these patterns are ways to save time, energy, and material when hardfacing, so you don’t have to coat the entire working surface of a piece completely.

Hardfacing Frequently Asked Questions

What does successful hardfacing look like? Ironically, hard facing often looks visually like bad welds because it’s an uneven and rough build-up of material on the surface of the workpiece. In a way, it’s almost like more of a “brute force” approach to welding rather than more elegant seams and connections.

What materials can and can’t be hard-faced? Hardfacing is generally done on harder steels, like stainless, manganese, carbon, and alloy steels. It can also be performed on cast iron, nickel-base alloys, and copper-base alloys. Other base materials are often too soft to take hardfacing well or are not used in the kinds of applications where hardfacing is beneficial.

One of the greatest details of hardfacing is that it’s only applicable to high-wear pieces in heavy industry. It’s typically not used in cases where direct wear isn’t responsible for damage. That is, cases where the cause of damage is flexing stress or sheer stress are not going to benefit from hard facing.

What’s the best process for hard facing? Many forms of hard facing are performed using submerged arc welding. Another popular process is flux-core arc welding. However, any welding process can be used for hardfacing, up to and including plasma arc welding, laser welding, and even brazing.

What matters most is the heat control and deposition rates of the process you choose. Some processes have better deposition rates and can hardface a workpiece faster and more effectively. Others need more careful control to avoid overheating the area. At the end of the day, though, what matters most is that you pick a process you’re familiar with and can control well.

What is “wear” in the industry? Most often, wear is caused by abrasion with a material like rock or aggregate or by impact. Sometimes, wear can be defined as metal-to-metal abrasion, heat, or corrosion, but these are less common in the cases where hard facing is most beneficial. Additionally, many different kinds of wear can apply at once; using an excavator to plow can cause both abrasion and impact, for example.

How can you pick the best machine for hardfacing? The best machine for hardfacing is one that can handle long duty cycles with enough power to deposit material quickly and limit the heat-affected zone of the base material. As such, nearly any good welder can handle the process, but it can benefit more from a 220v machine over a 110v machine. Either way, there are many options you can explore to find the welder that best suits your needs. Our welding equipment rentals help you test and try out machines and, if you don’t like them, return and rent different machines.

Red-D-Arc, an Airgas company, rents and leases welders, welding positioners, welding-related equipment, and electric power generators – anywhere in the world. Our rental welders, positioners and specialty products have been engineered and built to provide Extreme-Duty™ performance and reliability in even the harshest environments, and are available through over 70 Red-D-Arc Service Centers, strategically located throughout the United States, Canada, the United Kingdom, France, and the Netherlands, as well as through strategic alliances in the Middle East, Spain, Italy, Croatia, and the Caribbean. From our rental fleet of over 60,000 welders, 3,700 weld positioners, and 3,700 electric-power generators, we can supply you with the equipment you need – where you need it – when you need it.